Why is it important to replace doorknobs and knobs?

There are several reasons why you want to keep your doorknobs and handles in good working order.

Security: Old or damaged doorknobs and knobs can compromise the security of your home or office by making it easier for intruders to break in. A new high-quality doorknob or handle can improve the locking mechanism and provide better security.

Function: Worn or damaged knobs and handles can make doors difficult to open and close, causing inconvenience and frustration. Replacing them will ensure your door operates properly and smoothly.

Aesthetics: Doorknobs and handles can improve the overall look and feel of a room or space. Replacing them can help refresh the look of your home or office, making it look more modern and attractive.

Tools you need
For doorknobs and handles, you'll need the following tools:

Screwdriver/pliers/tape measure/hammer (optional - may be required if the latch or strike plate needs adjustment)/drill hole (optional - if the new doorknob or handle requires a larger hole than the existing one) might need)

It's important to note that the specific tools needed may vary depending on the type of doorknob or handle being replaced. Be sure to refer to the manufacturer's instructions for guidance on the tools and materials needed for your specific doorknob or handle.

Step 1: Remove the old door or handle
To remove an old doorknob or knob, follow these steps:
Find screws or fasteners: Look for screws or other fasteners that hold the doorknob or handle in place. They are usually located on the inside of the door or a panel around a knob or handle. Some door handles may have a set screw in the base.

Remove screws or fasteners: Use a screwdriver to remove the screws or other fasteners holding the old knob or handle in place. In some cases, the screws may be covered by a trim plate or cover and can be removed by gently prying.

Remove the old knob or handle: The old knob or handle should be easy to remove after removing the screws or fasteners. Simply pull it off the door, being careful not to damage the surrounding hardware.

Remove any remaining hardware: Depending on the type of doorknob or handle, there may be other door components that need to be removed, such as latches, strike plates, or panels. This can usually be removed using pliers or a screwdriver.

Be careful when removing old doorknobs or handles as there may be sharp edges or other hazards. Additionally, some older door handles may contain or other hazardous materials, so proper precautions should be taken when handling them.

Step Two: Install a New Door or Handle
Before installing new hardware, check the manufacturer's instructions to make sure all required components are included. Assemble your new doorknob or handle according to the instructions, making sure all screws and fasteners are tightened. Then perform the following steps:

Insert the new latch or spindle: If the new door hardware includes a latch or spindle, insert it into the corresponding hole in the side of the door. The latch or shaft should slide in easily and be flush with the edge of the door.

Attach the exterior knob or handle: Place the exterior knob or handle on the spindle, aligning all screw holes with the holes in the panel or trim plate. Insert the screws into the holes and tighten with a screwdriver.

Install an interior knob or handle: Follow the steps for interior door hardware above.

Install any add-ons: If you need to install add-ons such as strike plates or panels, follow the manufacturer's instructions.

Step Three: Test the New Door Hardware
After everything is installed, test the new door hardware to make sure everything is working properly. You can turn the knob or handle to make sure it operates smoothly and without resistance. Then follow these steps:

Turn the knob or lever to engage the latch or bolt. Make sure the latch or pin is fully extended into the strike plate or latch plate and that the door cannot be opened without turning the knob or lever.

Check the alignment of the strike plate or latch plate to ensure that the latch or bolt is properly aligned and fully engaged. If necessary, use a screwdriver and hammer to adjust the position of the strike plate or latch plate.

If the new doorknob or knob comes with a lock, test the lock to make sure it's working properly. Insert the key, turn it to lock and unlock the door, and make sure the deadbolt is fully extended and retracted.